The Fundamentals of Plumbing Skills When Installing a Bathtub
The Fundamentals of Plumbing Skills When Installing a Bathtub
Blog Article
We've noticed this post on Installing A Bathtub listed below on the web and concluded it made sense to talk about it with you over here.
Mounting a bath tub isn't specifically brain surgery, yet it does require solid plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult job. If the old bathtub is easily easily accessible, the task can relocate quickly; if you need to open a wall surface to remove the old tub as well as place the brand-new tub, the job is a lot harder. In either situation, the task is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub and embeded in the brand-new one. Ensure you have qualified on your own for the work and also fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is much better to take into consideration utilizing one before you begin. Opportunities are you may require an expert plumber to make tube links.
This short article will certainly assist you mount a new tub in your bathroom if you have currently bought a new tub and also don't require to transform the setup of your previous supply of water pipelines.
Your devices and material checklist must consist of the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bath should be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to stop pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its last placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing faucets can be quite troublesome because of the restricted gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Before moving on to fit the new faucets, compare the pipe links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Making use of the two wood boards under its feet, position the tub in the needed position. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make sure that the tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bath tub until the level checks out level.
To install faucets, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression join; after that do the very same for the various other tap.
Turn on the water and examine all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill the bath tub as well as likewise inspect the overflow electrical outlet and the regular electrical outlet for leaks.
Ultimately, fix the bath paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub must wait till the bathtub has been used a minimum of once as this will certainly resolve it into its last position.
Fitting New Taps
If the tails of the new faucets are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washers are in place in between the faucet as well as the sink. Protect the faucet in place with the manufacturer given backnut. When the faucet is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former type needs to be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to fracture a rigid seal, creating the water to pass through the wall between the bathroom and the tiling, resulting in issues with moisture as well as possible leaks to the ceiling below.
You can choose from a range of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, and also can securing spaces as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealer can break rather very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is a good idea to fit the ceramic tiles using water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader about How to Install a Bathtub, I imagined sharing that piece of content was a good idea. Liked our posting? Please share it. Help another person discover it. We appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Book Now! Report this page